H05 通用工艺 标准查询与下载



共找到 6 条与 通用工艺 相关的标准,共 1

本规范适用于新建铜冶炼厂的工艺设计,也适用于已有铜冶炼厂的扩建和改建工艺设计。

Code for design of copper smelter processes

ICS
CCS
H05
发布
2010-08-18
实施
2011-06-01

本标准规定了离子型稀土矿原地浸出开采安全生产的组织管理、目标管理、教育与培训、设计、施工、生产、应急管理、安全报告与统计分析等过程中的基本要求。 本标准适用于采用原地浸矿工艺生产的离子型稀土矿山(以下简称“矿山”)安全评价、设计、建设、生产。

Safety specification for in-situ leaching mining of ion-absorption rare earth ore

ICS
77.120.99
CCS
H05
发布
2016-07-11
实施
2017-01-01

Dieser Teil von ISO 3834 legt die Dokumente fest, deren Anforderungen erfüllt werden müssen, um die Übereinstimmung mit den Anforderungen nach ISO 3834-2, ISO 3834-3 oder ISO 3834-4 nachzuweisen. Er kann nur in Verbindung mit ISO 3834-2, ISO 3834-3 oder ISO 3834-4 angewendet werden.

Quality requirements for fusion welding of metallic materials - Part 5: Documents with which it is necessary to conform to claim conformity to the quality requirements of ISO 3834-2, ISO 3834-3 or ISO 3834-4 (ISO 3834-5:2015)

ICS
25.160.10
CCS
H05
发布
2015-06-01
实施

This practice is intended to provide guidance on the proper operation of pressure water-jet cleaning and cutting equipment. This practice is also applicable at lower pressures where there is foreseeable risk of injury. This practice is provided to assist persons unfamiliar with the operation of water-jet cleaning and cutting equipment in learning to correctly use the equipment. Correct operation and use of the pressure water-jet cleaning and cutting equipment is the responsibility of the operator and employer. After the operator has familiarized himself with the identification of pressure metal fittings, hoses, guns, and accessories in accordance with the original equipment manufacturer''s specifications, instructions, and programmed instructional material, hydrojetting may begin. Modification of water-jetting equipment shall not be done without prior written approval by the manufacturer of the equipment. Employees shall be instructed in the recognition and avoidance of unsafe conditions. Note 28212;Warning: Serious harm or injury may result from the misuse of water-jetting equipment and the use of improper fittings, hoses, or attachments. The use of pressure water-jet equipment for cutting and cleaning is a rapidly evolving technology. This practice will be periodically reviewed for any required changes at least every five years. ^SCOPE: 1.1 This practice covers the personnel requirements, operator training, operating procedures, and recommended equipment performance/design for the proper operation of all types of pressure water-jet cleaning and cutting equipment as normally used by industries concerned with construction, maintenance, repair, cleaning, cutting, and demolition work. 1.2 The term high-pressure water jetting covers all water jetting, including the use of additives or abrasives at pressures above 100.5 psig (0.69 MPa). 1.3 Any person required to operate or maintain pressure water-jetting equipment shall have been trained and have demonstrated the ability and knowledge to do so in accordance with the original equipment manufacturer''s instructions, specifications, and training programs. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Notes 1-8 and Sections 8 and 11 for specific hazards statements.

Standard Practice for Pressure Water Cleaning and Cutting

ICS
25.220.20 (Surface treatment)
CCS
H05
发布
2008
实施

Quality requirements for fusion welding of metallic materials - Part 6: Guidelines on implementing ISO 3834

ICS
25.160.01
CCS
H05
发布
2007-02-01
实施

1.1 This practice covers the personnel requirements, operator training, operating procedures, and recommended equipment performance/design for the proper operation of all types of pressure water-jet cleaning and cutting equipment as normally used by industries concerned with construction, maintenance, repair, cleaning, cutting, and demolition work. 1.2 The term high-pressure water jetting covers all water jetting, including the use of additives or abrasives at pressures above 1005 psig (6.9 MPa). 1.3 Any person required to operate or maintain pressure water-jetting equipment shall have been trained and have demonstrated the ability and knowledge to do so in accordance with the original equipment manufacturer's instructions, specifications, and training programs. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.5 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Notes 1 through 8 and Section 8 for specific hazards statements.

Standard Practice for Pressure Water Cleaning and Cutting

ICS
25.100.01;25.220.20
CCS
H05
发布
1998
实施



Copyright ©2007-2016 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号