H08 标志、包装、运输、贮存 标准查询与下载



共找到 11 条与 标志、包装、运输、贮存 相关的标准,共 1

1.1 This practice establishes the physical item marking requirements for identification purposes for aluminum and magnesium products. Package marking for shipment and inspection acceptance is not within the scope of this standard. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Standard Practice for Identification Marking of Aluminum and Magnesium Products

ICS
77.150.99 (Other products of non-ferrous metals)
CCS
H08
发布
2008
实施

이 규격은 배관 시스템의 제작에 쓰이는 페라이트계 및 오스테나이트계 강관의 시각적으로 연속

Steel tubes-Continuous character marking and colour coding for material identification

ICS
01.070
CCS
H08
发布
2005-12-22
实施
2005-12-22

이 규격은 배관 시스템의 제작에 쓰이는 페라이트계 및 오스테나이트계 강관의 시각적으로 연속

Steel tubes-Continuous character marking and colour coding for material identification

ICS
01.070
CCS
H08
发布
2005-12-22
实施
2005-12-22

The purpose of these color codes is to allow for quick identification of ingot bundles or jumbo ingots of alloys used for hot-dip galvanizing. Other than jumbo ingots, this standard is not intended to imply that each ingot will be color-coded but only that each ingot bundle be color coded. Each ingot bundle or jumbo ingot shall be identified with the appropriate color code listed in Table 1. The color will be applied as a stripe, or stripes, on two adjacent sides of the ingot bundle or jumbo ingot. The color stripes will be applied to include the ingot bundle foot. When using multiple stripes, the colored stripes will be applied from left to right as indicated in Table 1. In the absence of a written agreement to the contrary between the supplier and end user, the North American color code will be the standard for all North American transactions; for all other transactions the International Color Code will be used.1.1 This standard is published with the following objectives: 1.1.1 To establish standard color codes for zinc, zinc alloy and zinc master alloy ingot used by the Hot-Dip Galvanizing industry, and 1.1.2 To standardize the use and application of these color codes. 1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

Standard Practice for Color Codes on Zinc and Zinc Alloy Ingot for Use in Hot-Dip Galvanizing of Steel

ICS
77.150.99 (Other products of non-ferrous metals)
CCS
H08
发布
2003
实施

This standard specifies the code letters to be allocated to define the metallurgical condition of metallic semi-finished products in delivery condition, for aerospace applications.

Metallic materials - Coding of metallurgical condition in delivery condition

ICS
49.025.05;49.025.15
CCS
H08
发布
1994-06-15
实施
1994-06-15

Bar Coded Transport and Handling Labels for Steel Products

ICS
CCS
H08
发布
1992-01-01
实施

This International Standard specifies the requirements for the optional continuous character and colour marking of ferritic and austenitic steel tubes that are used in the fabrication of pip-ing systems. The colour coding specified can also be used for the marking of fittings and components (see 6.2.3). It covers specific requirements for definitive material identifica-tion by the use of printed characters which are applied repetitively (continuously) along the length of the tube, and for the colour coding of discrete groups of steels. The colour cod-ing may be specified at the option of the purchaser and is in-tended for use only in conjunction with the definitive character marking requirements given in clause 5. In the absence of a suitable International Standard defining colours suitable for use in colour coding, annex A makes reference to certain equivalent colour codes given in national standards which may be used. It is recognized that this International Standard can only be applied by agreement between the parties concerned.

Steel tubes; continuous character marking and colour coding for material identification

ICS
23.040.10
CCS
H08
发布
1990-04
实施
1990-04-01

Iron and steel - Marking of steel plates with piercer or paint

Iron and steel - Marking of steel plates with piercer or paint

ICS
CCS
H08
发布
1983-09-01
实施

本方法适用于测定防潮用含纤维基材的低透湿率的复合包装材料的透湿率,也可用于其它塑料薄膜包装材料。

ICS
CCS
H08
发布
1982-07-23
实施
1982-10-01



Copyright ©2007-2016 ANTPEDIA, All Rights Reserved
京ICP备07018254号 京公网安备1101085018 电信与信息服务业务经营许可证:京ICP证110310号